Lastest BMW Multi Tool CAS1-3 + Key Programmer

          Lastest BMW Multi Tool CAS1-3 + Key Programmer

Powerful than AK300!!!

Version: V2.2

BMW Multi Tool includes forth parts, hardware device, dongle, programmer, software. Before running software you must connect dongle and hardware device to computer.

Descriptions

1. OBD II CONNECTOR: Connect the tool to the vehicle's Data Link connector (DLC).
2. Dongle: USB dongle.
3. USB CONNECTOR: Connect the tool to the PC/Laptop through USB Cable.
4. Programmer: Program keys.
5. Programmer Female Pin: Connect programmer to device.
6. Programmer Male Pin: Connect programmer to device.

Specifications

1.Operating Temperature: -20 to 70 °C ( -4 to 158 °F )
2. Storage Temperature: -40 to 85 °C ( -40 to 185 °F )
3. Diagnostic Interface: 16 PIN
4. USB Interface: USB 2.0
5. Power: DC 5 V - 12 V
6. Consumption: 1 W
7. Dimensions: Length 95 mm, Width 49 mm, Height 28 mm

Function

2. Protocal type
Now BMT support there type of protocol: KWP-CAN BUS 100Kbps, KWP-CAN BUS 500Kbps, KWP-2000. "Auto Detect " function can help you to choose the right protocol. After choose protocol okay, then press "Connect". If connected success. All CAS info will display in CAS Identification. Include CAS number, VIN, production date, etc.

3. EEPROM Function
Read EEPROM, Write EEPROM, Save File, Load File…
1). You should backup the CAS EEPROM before prepare dealer key. After succeed read EEPROM, please save it as back file. This step is very important.
2). Now can't read the whole EEPROM for cas3 system. But the main section is contained. It should be saved. When you read CAS EEPROM, it will give tips (Press ok to continue).


After success reading it, you will get

Write EEPROM function is only support CAS1, CAS2 system. Doesn’t support write to cas3 system.

4. Odometer
Support read and change KM stored in CAS system.
Don't support to change KM in instrument. If you want to change the KM display in instrument. You should change KM in CAS system first. Then modify the KM in instrument manually.

Read KM

When you try to read KM from CAS system,you will get the following tips:Press OK to continue

5. Synchronization Codes
1). CAS3 code-DME, CAS3code-EGS: Read and write DME and EGS code stored in CAS3 system.
2). Synchronize DME and CAS— this function will be useful while prepare dealer key or any other operation which cause can't start the engine.
3). Synchronize CAS and ELV — this function can help clear wheel errors

6. Key Learn


Function Introduction

1). Get Key Info: With this function you can get the key cutting, remote frequency, and key data.
2). Save Key Info: Save the read key info.
3). Load Key Info: Load the saved key info. To see the key data and prepare for write key info.
4). Write Key Info: Write the loaded key info into CAS system.
5). Make Dealer Key: You can prepare dealer key after you get key info successfully. Also you should choose the key position.
6). Add key: Add the new dealer key into CAS system. Some CAS system needs this step to start the engine.
7). Enable Key: Insert the current key into ignition switch, press "Enable Key". The key after current key will be enabled.
8). Disable Key: Insert the current key into ignition switch, press "Disable key". The key after current key will be disabled.
9). Clear DTC: Before prepare dealer key and after it you can use this function to clear DTC.
10). Clear Shadow: Before prepare dealer key and after it you can use this function to clear Shadow.

7. File Make Key


1). Choose CAS or EWS type.


2). Load the choose EEPROM file you will get the make dealer key window.


3). Choose key position and press "Make Dealer Key" button. Flow the given tips to prepare dealer key. After succeed you can save the new EEPROM dump file.
- For EWS1, EWS2, EWS3, EWS4, CAS1, CAS2, CAS3 type the prepared dealer key can start the engine directly.
- For some CA3+ type you need to write back the new dump file into car.


4). CAS3 encrypt data, only OBDII prepare make key is support for CAS3 encrypt data.

8.Device Update
Open this window after connect to internet. You can see the latest software version, firmware version, dongle version. You can go to our website for further information. After succeeded update device firmware, must reconnect the hardware to computer.
\

1.Device Info: Get dongle and hardware SN and version.


2.Device Update: This function can update the dongle and device.



Process to prepare dealer key

1. On main window choose “Connect” to auto detect the current car protocol and get the CAS info.
2. On main window choose “Read EEPROM” to read the CAS EEPROM file and save it.
3. On main window choose “Key Learn” button to get key learn window.
4. On Key Learn window choose “Get Key Info” to get the key info stored in CAS system.(picture 2).
5. Choose “Save Key Info” button to save the read key info for backup.
6. Check the connection between programmer and device. Keep connection while make key process.
7. Put new blank key into the center of programmer.
8. Choose the position where you want to suit the key.
9. Press “Make Dealer Key” to prepare dealer key. After succeed you will get (picture 3)
"Key make okay and locked. Please use it start the car. If can’t start engine, use “Add Key” function add the new dealer key to CAS system.” Once can start the engine, go to step 13.
10. Put the new dealer key into programmer. Use “Add Key” function to add the key to CAS system. After that you will get (picture 4):”New dealer key success written to CAS system. You can start engine with the new key now. If can’t please use the original working key first.”
11. Please return to main widow and use function “Synch DME-CAS” to synchronize DME (ECU) with CAS.
12. Use “Synch CAS-ELV” to clear wheel errors.
13. Enter to key learn window use “Clear DTC” and “Clear Shadow” function clear all error sin CAS system.
While prepare dealer key process. Once you get the tips like picture 1, remove the key from ignition switch, if key has keyless, take the key out of car.

Picture 1:


picture2:

picture3:

picture4:


Warning: Make sure connect dongle to compute before run the software.

"Device not connected”Error
Information: Hardware not connected to PC with USB port.
Solution: Plug device to USB.

Any questions, please feel free to contact us
Email: sales01@autodiag.de

1. Car access sytem dentification

2. Read/Write CAS EEPROM(OBDII)

3. Read/Write KM stored in CAS system(OBDII)

4. Read/Write synchronization codes stored in CAS system(OBDII)

5. Synchronize DME and CAS(OBDII)

6. Synchronize CAS and ELV(OBDII)

7. Prepare dealer key for CAS1/CAS2/CAS3/CAS+(support latest CAS3 verison)(OBDII)

8. Read/Restore CAS KEY information(OBDII)

9. Disable/Enable key with working key(OBDII)

10. Clear DTC and Shadow (OBDII)

11. Prepare dealer key with CAS eeprom dump

12. Unlock dealer key prepared with our software with CAS eeprom dump or KEY information

13. Change KM in CAS and instrument dashboard with file dump

14. Have key programmer, you can programm dealer key directly.

Pay attention to the function: Help->Device update. You can get the latest software version and firmware verion when you can access to internet.

1. Menu

- Tool: you can choose language here, support "English" and "Chinese Simplified" Restart software to apply your settings.
- File Make Key: you can prepare dealer key with EWS and CAS EEPROM dump.
- Help: Device update. You can get your device and dongle id version and update it.